59 Bike Maintenance Tips Every Cyclist Should Know
(60-101, next month!)
YOUR GUIDE TO A LONGER LIFE FOR YOUR BICYCLE AND GEAR.
BY JENNIFER SHERRY AND THE BICYCLING EDITORS
Apr 22, 2021
Your bicycle doesn’t run on leg power alone. It also needs a little lube, a lotta love, and a good listen. You may not know every remedy your bike needs to live a long life, but you can gain enough wisdom along the way to keep it in tip-top shape and out of the shop with proper bike maintenance.
This collection of mostly timeless advice (until advances in bicycle technology make some of it obsolete) will guide you through the role of primary caregiver—so you can leave the tough stuff to the professionals.
Good Rules of Thumb
No. 1 Never loan tools to friends.
No. 2 If it’s threaded, grease it.
No. 3 You can’t properly adjust a bicycle that is dirty and not lubricated.
No. 4 Perfect the art of changing a flat. No excuses.
No. 5 Nylon tire levers are better than metal ones.
No. 6 Measure twice, then cut. This especially goes for steerer tubes and integrated seatposts.
No. 7 When disassembling something, keep track of the order in which you remove parts. It takes the mystery out of putting it back together. (Pro tip: Set up your smartphone to video the disassembly for an easy reference guide.)
No. 8 Check tire pressure before every ride, especially if you’re running tubeless.
No. 9 The three most important tools to have on a ride: a multitool with a chain breaker, a pump or CO2, and a patch kit or tube.
No. 10 When tinkering with anything near your cranks, shift into the big ring first so you don’t mangle your hand on the chainring teeth.
No. 11 Periodically check for bearing play in your headset, hubs, and cranks. To check your headset, squeeze the front brake and rock your bike fore and aft. For wheel and crank bearings, pull the wheel or crank side to side. If you feel a wiggle, your component needs an adjustment. Don’t ignore it, or the problem will get bigger and more expensive.
No. 12 Using a torque wrench (see No. 81), check the tightness of your crank bolts every month. If you just bought a new bike, check them after every ride for the first week.
No. 13 After you box your bike for travel but before you seal it, give it a side-to-side shake to note any loose or rattling parts. Then secure them.
No. 14 Loctite Threadlocker Blue 242 is a must-have accessory for bolts that assemble using standard hand tools. It seals threaded fasteners and keeps them from rattling loose due to vibration.
Squeaks, Creaks, and Squeals
No. 15 If your bike makes a noise, it’s trying to tell you something. Don’t ignore it.
No. 16 A creaky crank is likely loose on the spindle. Remove the crank bolts, lubricate the threads, and reinstall. Tighten everything using a torque wrench.
No. 17 Use a light lubricant to silence squealing rear-derailleur pulley wheels.
No. 18 If your saddle creaks, drip a few drops of oil on the rail where it connects to your saddle and into the clamp where it grips the rails. (But before you do that, make sure that the area is fully clean and free of dust and grime—a good cleaning might solve the problem.)
No. 19 Master the skill of wrapping a handlebar.
No. 20 Create an ‘easy charge’ station near where you store your bike so you can easily plug in your cycling computer, bike lights, and even your electronic shifting post-ride, so you never lose power halfway through a century again.
Respect Your Mechanic
No. 21 Don’t be a hero. Whether it’s due to lack of knowledge or experience, or not having the proper tools for the job, you are not capable of every repair. Sometimes you have to take your problem to a professional.
No. 22 Find out what your shop mechanic’s favorite afternoon munchie is, then bring it along the next time you stop in for a repair.
No. 23 It doesn’t matter how you broke it. Just don’t lie to your bike mechanic.
No. 24 Never roll your bike into the shop and expect an on-the-spot repair. You don’t know what your mechanic is up against on any given day.
These Are the Brakes
No. 25 Three signs your brake pads are worn: You hear a gritty scraping sound, the grooves in the pad have all but disappeared, or you feel stickiness when you brake.
No. 26 Don’t touch disc-brake pads with your fingers. The oil from your skin can decrease their braking power.
No. 27 Work on one brake at a time so you always have an intact brake to reference.
No. 28 Always remove disc-brake pads when bleeding your brakes. Use a spacer, like Avid’s bleed block, to hold the pistons in place.
No. 29 If you’ve been running bolt-on brake pads and it’s time to replace them, now is the time to switch to the cartridge-style type. The next time your pads need replacement, you can simply slip them into the holder, no alignment needed.
No. 30 After removing a disc-brake wheel from the frame or fork, do not squeeze the brake lever. Doing so can cause the brake pads to clamp together tightly—and separating them is no easy task.
No. 31 When replacing a brake cable, initially adjust it so the pads are fully against the rim, then squeeze the brake lever as hard as you can a few times to release slack in the cable and compress the housing. Repeat these steps until you don’t feel the cable and housing give anymore. Now adjust your brakes the way you want them to feel.
No. 32 Use sandpaper to roughen up glazed brake pads.
No. 33 Snug down your brake levers with a rubber band when adjusting rim-brake pads.
Need to Know
No. 34 Do not use a solvent to lube your chain.
No. 35 If your wheel doesn’t sit straight in your bike after a hub overhaul, make sure the springs on the quick-release are installed correctly. The tapered end should always face in.
No. 36 Over time, the sealant on your tubeless setup dries out and becomes less effective at preventing leaks. Refresh it every three months (or every month if you have a mountain bike).
No. 37 Lots of experts tell you to use a level on your saddle as a starting point for comfort. What they might forget to mention: Your bike has to be on a level surface for this to work properly.
No. 38 Forget which kind of valves you have? Schrader valves are similar to the ones found on your car; presta valves are thinner, with a small nut that has to be opened prior to inflation.
No. 39 Places where grit hides: in brake pads, between tubes and tires, in cleats and pedals.
No. 40 If a carbon part moves when it’s not supposed to, it can get scratched or trashed.
No. 41 If you pinch-flat often, the PSI (air volume) in your tires is almost certainly too low.
No. 42 The difference between an axle and a spindle: An axle remains stationary while something rotates around it (think wheel); a spindle revolves inside a stationary body (think bottom bracket).
No. 43 Pluck your spokes often so you get to know what feels and sounds right. When one feels off or its tone is different from the rest, you know you have a loose spoke.
No. 44 Install quick-release skewers so the levers are on the non-driveside.
No. 45 The easiest way to get your rear wheel out is to shift into the highest gear so your chain is on the outer (smallest) cog. If it’s in the middle or all the way to the inside, you’ll have a harder time getting the cogs past the chain and derailleur.
No. 46 If the type on your front hub doesn’t read left to right as you sit in the saddle, your wheel is installed backwards.
No. 47 Most newer bikes have a sealed-cartridge bottom bracket, which means you could get three to five years out of it (even if you ride a ton) and never have to touch it. In fact, if yours loosens or wears out, it’s easiest to just buy a new one. The swap takes about 15 minutes but is best left to your mechanic—not because it’s difficult but because it’s cheaper to pay someone than to buy the tools you’ll need but rarely use.
___________________________________________________________________________________________________________________________
Cable and Housing Assistance
No. 48 Avoid a shredded fingertip. Always cap off the end of a freshly cut cable.
No. 49 Cut cables using a bike-specific cable cutter. You’ll get a cleaner cut, with no frayed ends on cables or sharp burrs on housing.
No. 50 Never use brake housing with shift cable or shift housing with brake cable.
No. 51 A few drops of Teflon oil in cable housings can fix sticky braking or slow shifting. (Don’t try this with electronic shifting, though!)
No. 52 When installing new cable, use your old cable housing as a guide when cutting new housing.
No. 53 Cut shift housing square and brake housing at an angle.
No. 54 Use a metal ferrule at the housing entrance to the rear derailleur rather than plastic, which can crack easily with looped entrances.
No. 55 If you store your tools in a toolbox, color-code them with their corresponding drawers or slots. If you have a pegboard in your shop, trace each tool in the spot where it hangs. Everything will be easier to find.
No. 56 No matter how long it takes, invest in quality bike tools until you have a complete set of the basics. See our list of essential tools.
No. 57 When doing a full tuneup, work from front to back or top to bottom so you’ll know where you were should you get interrupted.
No. 58 When you disassemble something complicated, use your smartphone or digital camera to document the process. If you end up with an extra part after reassembly is complete, you can look back at your pics to figure out when and where things went wrong.
No. 59 Never turn your bike upside down to work on it. You could ruin cables, accessories, even your saddle. If you don’t have a repair stand, find a way to suspend it.
More next month! |